New Cars Specification
Wednesday, June 12, 2013
Mr Toyoda Goes To Washington
Full press release (remember, we said "brief") here.
Monday, June 10, 2013
Podiums with his own hands in 2108
Many people know how to make the podium for the "textile" technology. If we judge by the information that comes in late, in the manufacture of professional and amateur designs the technology pushed more labor-intensive and sophisticated technology. In applying these technologies is used polyurethane foam. And yet, this technology early to write off because it can easily make podiums without special fitting. You can make perfect in its form podiums. This can be seen on the example of making the podium, designed for the WHA 2108. To begin, we take 2 rings, the height and diameter should be slightly more tweeters. This is to ensure that it is possible to install them flush. Then we take: epoxy, sewer PVC pipes (50 mm), a piece of knitted material, hot melt glue, sandpaper and filler having a composition of glass. Also need vinyl or antigravy with paint Eska 5104, which can be used as a decorative material. First we need to clean off coating from the surface of the rack. To do this, use the medium grit sandpaper. Pre-defined ring binds in the appropriate places melting. The resulting product should obtyanut piece of knitted material. Then sew the edge and gently span fabric. Now it is necessary to dissolve the epoxy. At first glance this procedure seems to be very simple. But in reality it is not. If Nedolya hardener, then freezing will last very long, and if it is poured - the resin will be very fragile. Do not rush to apply resin to the surface. First drip it onto paper, nagreem tile or a soldering iron. If you lit it properly, gum boil. When the resin has cooled, it could easily be broken. If not, add a little more hardener. Saturate fabric with epoxy resin. Do not forget to leave a site in the center of the circle without impregnation. It is necessary to avoid bloating. Typically, about 30 grams of resin impregnation Half will go to. You can add a bit of aluminum powder, which is also used as a hardener. This will help identify possible defects on the surface and contributes to better handling. Once the resin hardens, processed drips from her soldering iron and sandpaper. Then cleaned out our product. At the same time try not to get to the tissues. We cut a hole for the speaker, and caused filler. Putty should be applied fairly thinly. Then we clean the sandpaper. Decorative finish is as follows: pre-degreased surface, applied several coats antigraviya. As a result, we obtain a surface that looks like shagreen. Treat the surface composition Kerru KR-970, after which the surface is similar to plastic, which is used to facing. Dyeing, the podium after starting to dry completely antigraviya. For this we use the paint Eska 5104. Paint color is "graphite" and "black". It is designed for painting plastic. The only drawback - the lack of aerosol packaging. If you do not spray, use the Dupli-Color cartridges or VHT. They are painting a dark gray color, suitable for painting vinyl and plastic. After staining the dried product and make the necessary hole for the wires.
Saturday, June 8, 2013
UPDATE Make That 41 000 For A Single Volt
Thursday, June 6, 2013
Alfa Comes Back To The USA
Tuesday, June 4, 2013
Changing the timing belt car Toyota 1G
The reasons for the timing belt wear (RM) may be different, but the two main - the age of the vehicle and the quantity of run. The more mileage, the more reasons to replace the timing belt. Series engines 1G Toyota cars are good because when you open the hood all the units of this engine are viewed very well, which greatly facilitates the work and it takes a little work time. Before replacing the timing belt wait for the engine to cool down, because the engine heat will not be able to achieve the desired belt tension. In the early work necessary to remove the air filter, resonator and tube cooling system. Then be sure to disconnect the battery, remove the hose leading to the radiator, the rim of the fan, V-shaped straps, disconnect which requires special care, and the actual radiator fan. Candles are not necessarily to shoot, but experts recommend to do this is to avoid high compression engine at the first scroll down after installing a new belt. Before removing the shrouds that cover the timing belt, you need to remove the crankshaft pulley, for this purpose need a special puller to remove the pulley. Keyway crankshaft at the same time must coincide with the keyway pulley. Sam crankshaft to rotate clockwise. Crankshaft can be rotated only when wearing a belt to avoid being struck on the valve piston. Please note that on the back of each gear has a label, which coincides with the tide on the motor housing. It is here that need to start shooting belt, loosening the guide and tension rollers. Do not forget to check whether the timing belt on oil, if the belt is dirty, you need to figure out where the leak. Once you have removed the belt, guide and tensioner need to set in place. In this case, a guide roller fastens you completely, but the tension - a little, but so that he hung around. You are now ready to tension the new belt. New timing belt put on in the following sequence: first, to the crankshaft, then the oil pump, guide rollers, pulleys camshaft, and only then on the tension wheel. In this movie needs a little weakened, he will shift to the right by a spring and a belt natyanetsya. Specifically draw roller is not needed. Once the timing belt to tighten, the crankshaft 2 - 3 times strictly in a clockwise direction. It should be done cautiously, slowly. Cranking the crankshaft counterclockwise will cause that the timing belt natyanetsya wrong that can lead to inoperable motor. After that, carefully check the labels on the gears. If the tags are identical with the tides on the body of the engine, turn the crank a few more times. Otherwise will have to start pulling the timing belt again. Once you've verified that the belt is tensioned correctly and all tags are identical, you can start the engine. Without those parts that you removed from the start, the engine can operate safely for about three minutes. Before you start the engine, make sure the transmission is in neutral. If the engine fails to start, as usual, this means that the timing belt tensioned correctly, and can be set in place all removed at the beginning of the parts in reverse order.
Sunday, June 2, 2013
Stickers still Beautiful Car Paint More Durable
Before installing the decal, first check the quality of paint. Original paint that still will not be disturbed if fitted sticker. But that does not paint a full body re likely to be peeled off if the sticker is removed. If repainted but only in-SPET in part, would be peeled off. Most car owners do not understand this and tend to blame the mounting stickers.
High-quality adhesive stickers will not damage car paint if exfoliated. One nice feature is the sticker glue is odorless. Available colors are also brighter and stronger, just like the color of car paint. Good quality can last up to 5 years. But a year is cheap wrote faded or peeling.
Car paint now that most contain elements of metallic colors require more rigorous treatment if fitted sticker. Installation of a sticker that simply stipping or certain motifs are advised not done for long periods of time. The reason is, this will make the paint become discolored if the sticker is removed. If not cleaned often and frequently bronzed, the use of stickers may still survive 1-2 years. But if rarely cleaned and are often hot, the paint was not covered stickers will be more dull than the paint that covered the sticker. This does not happen if the sticker attached nge-block the entire body. Even more durable paint.
The sticker is mounted on the car, attempted not exposed to drugs whose shape cream cleanser. Drug-shaped cream is left on the pore surface of the sticker, not as fluid is more easily cleaned with water. This will make the colors more stickers fade and not shiny anymore. Because it is porous, the more frequent washing, car stickers will be more shiny.rs
Why Car Oil Fast Out
First, there was a leak in the seals and packing on the sidelines of the machine. So that the leak was made dropwise oil wasted during engine combustion process takes place. Another indication, if our car exhaust white smoke when the car is running. It could be because the oil that burned in the combustion process, caused by leakage at the piston ring.
The fix, if its because of leaks in the seals and packing, will inevitably have to dismantle the machine, to check and replace a new seals and packing if indeed the source of oil leaks from there. Then, compression can also check the car, with the cylinder head to disassemble it. Check whether the condition of the piston ring is qualified or not to hold the oil does not burn chamber infiltrates.
The most common means there are two causes why the oil run out quickly, could be due to a leak or because the oil was also burned in the combustion process because the ring Seker was no longer able to hold oil.